Outlet AMJ45 8/8 K Up/50 Cat.6A alpine white
Outlet AMJ45 8/8 K Up/50 Cat.6A alpine white
Technical attributes
| Article name | CU-Out AMJ45 8/8K UP/50 C6A cduct alpwt |
|---|---|
| Type | cable duct mounting, 2xRJ45 |
| Colour | alpine white |
Description of the Series/Product Category
Notice: The following information refer to the series/product category as a whole. Please see the specific datasheet for specific technical information of a particular product.
Performance characteristics
Transmission performance: Cat.6A acc. to ISO/IEC 11801; EN 50173-1
fully shielded
360° shielding contact and strain relief by means of two (one in the case of Cat.5e) separate, captive screw clamps for the exterior cable jacket and shielding
can be wired up from all directions, in 8x45° steps
either horizontal or vertical installation in the cable duct as a result of variable cable inlet
Type offers low installation depth; problem-free installation in floor tanks as a result of cable inlet from the side within the subfloor mounting box
option of plug-in ground connection at all four corners; according to DIN 46342-1; 6.3 mm
can be combined with covers of a wide variety of switching programs
Independent AP design available, an AP add-on set is not required
faceplate can be retrofitted with a flip-up loss-proof, transparent label field
protection flaps
1-way (8) and 2-way outlets (8/8, 2x8(4)) available
stable, compact, ergonomic construction, that provides secure hold during installation
Mechanical attributes
| Material: housing | PBT UL94 V0 white |
|---|---|
| Insertion force | ≤ 30 N |
| Life (mating cycles RJ45, RJ12, RJ11) | ≥ 750 |
| Conductor diameter | solid 0,4-0,65mm AWG26/1 - AWG 22/1 |
| Material: PCB | FR4 UL94 V0 |
| Material: PCB finish | tin plated |
| Core Diameter | 0,7 - 1,6 mm |
| Material: contact spring | spring steel |
| Reusable contacts | ≤ 50x |
| Material: contact spring finish | min. 0,8 μm Au over 1,2 μm Ni |
| Material: contact IDC termination | CuZn |
| Material: IDC termination finish | tin plated |
| Material: shielding housing | zinc diecast |
| Material: jack housing | PBT weiß |
| Material: insulating plate | PA black |
| Material: shield | German silver |
| Material: screw | steel zinc plated |
Elecrical attributes
| Contact resistance | ≤ 20 mΩ |
|---|---|
| Insulation resistance | ≥ 500 MΩ |
| Voltage proof: contact-contact | ≥ 1000 V, DC |
| Voltage proof: contact-shield | ≥ 1500 V, DC |
| PoE+ acc to IEEE 802.3at | Adequate for Power over Ethernet+ |
| Transfer Impedanz |
for 1 MHz < 100mΩ for 10 MHz < 200mΩ for 80 MHz < 1600mΩ |
| Current carrying capacity at 50°C | 1 A |
| PoE according to IEEE802.3af | Adequate for 4 Pair Power over Ethernet |
Transmission properties
| 10 Gigabit Ethernet acc. to IEEE 802.3an | Adequate for 10 Gigabit Ethernet |
|---|---|
| Category 6A | ISO/IEC 11801; DIN EN 50173-1 ANSI/TIA/EIA-568-C.2 |
| Class E^A | ISO/IEC 11801; DIN EN 50173-1 |
Norms
| Connectors | IEC 60603-7-51 |
|---|---|
| Generic cabling systems | ANSI/TIA/EIA-568-C.2 ISO/IEC 11801 DIN EN 50173-1 |
Environmental requirements
| Ambient temperature | -40° C to + 70° C |
|---|---|
| Protection against particulate ingress | IP2X |
| Protection against water / immersion | IPX0 |
Accessories
Accessories